[Postname]
Name=Brigdeport TNC_426
KopfZeile=

[Modul]
PostModul=
SIMModul=

[StartCommand]
Command1=(Count_Block) BEGIN PGM (NCFilename) Inch
Command2=(Count_Block)(TOOL_DATA)
Command3=(Count_Block) BLK FORM 0.1 Z X(BX-)  Y(BY-)  Z(BZ-)
Command4=(Count_Block) BLK FORM 0.2  X(BX+)  Y(BY+)  Z(BZ+)
Command5=(Count_Block)(SPINDLE_Block)
Command6=(Count_Block) M6
Command7=(Count_Block) TOOL DEF (TNrNext)
Command8=(Count_Block) L X(KFAx+[0]) Y(KFAy+[0]) R0 FMAX(SpiCW)
Command9=(Count_Block) L Z(KFAz+[0]) FMAX(CoolOn)

[EndCommand]
Command1=(Count_Block) L Z0 FMAX M92
Command2=(Count_Block) M30
Command3=(Count_Block) END PGM (NCFilename) Inch

[GENERAL]
BlockPrefix=
BlockEndPrefix=
Extension=.h
Decimal=.
OutputPlus=+
CommentStartChar=;
CommentEndChar=
XYPlane=
YZPlane=
ZXPlane=
LinetoCircle=1
LinetoCircleToleranceFactor=1.0
LinetoCircleRadius_MAX=1500
LinetoCircleSegment_MAX=5
LinetoCirclePlane_Code=1
GModal=0
CountChar=
NUMPlaces=
Increment=1
StartUnit=0
Char1=
Char2=
Char3=
Count_Block=(CountChar)+(Count)
CoolOn=(ope[(RNrL+[0])=1? M8: M7])
CoolOff= M9
TimeFactor=1.200000
ZAxisMaxFeedFactor=0.500000
OUTSCAL=1.000000

[LINEAR DEFINITION]
LinearMotion=(FEEDRATE_Block)
RapidMotion= FMAX
KoordxChar= X
KoordyChar= Y
KoordzChar= Z
DecimalPlaces=3
XFactor=1.000000
YFactor=1.000000
ZFactor=1.000000
ShowZeros=3
LZERO=1
Char1= L
Char2=(\n)(Count_Block) L X(KFA[(getXp)]) Y(KFA[(getYp)]) Z(KFA[(getZp)])
Char3=
G40Comp= R0
G41Comp= RL
G42Comp= RR
XYZModal=1
LinearRegisterPosition=(Count_Block)+(SPINDLE_Block)+(Char2)+(Motion)+(Backlash)+(Count_Block)+(Char1)+(KoordxChar)+(Koordx)+(KoordyChar)+(Koordy)+(KoordzChar)+(Koordz)+(CompOff)+(CompLeft)+(CompRight)+(FEEDRATE_Block)+(Motion)
RapidRegisterPosition=(Count_Block)+(SPINDLE_Block)+(Char2)+(Motion)+(Backlash)+(Count_Block)+(Char1)+(KoordxChar)+(Koordx)+(KoordyChar)+(Koordy)+(KoordzChar)+(Koordz)+(CompOff)+(CompLeft)+(CompRight)+(Motion)

[ROUNDAXIS DEFINITION]
KoordaChar=
KoordbChar=
KoordcChar=
DecimalPlaces=
AFactor=
BFactor=
CFactor=
ShowZeros=
LZERO=
Char1=
Char2=
Char3=
ABCModal=0
CharCW=
CharCCW=
ARotaryLimitMin=-999999
ARotaryLimitMax=999999
BRotaryLimitMin=-999999
BRotaryLimitMax=999999
CRotaryLimitMin=-999999
CRotaryLimitMax=999999
AoppositeDirect=0
BoppositeDirect=0
CoppositeDirect=0
RadianOutput=0

[CIRCLE DEFINITION]
CIRCLE_R= DR-
CIRCLE_L= DR+
XZ_CIRCLE_R= DR-
XZ_CIRCLE_L= DR+
YZ_CIRCLE_R= DR-
YZ_CIRCLE_L= DR+
KoordiChar= X
KoordjChar= Y
KoordkChar= Z
RadiusChar= R
AngleChar= IPA
HelixChar= CP
I_Factor=1.000000
J_Factor=1.000000
KR_Factor=1.000000
W_Factor=1.000000
ShowZeros=3
Char1= CC
Char2=(\n)(Count_Block) C(IF[(getPL)<3]{)
Char3=(FEEDRATE_Block)
Char4=(ope[(getPL)=3? X(KFAx+[0]):(ope[(getPL)=2? Y(KFAy+[0]): Z(KFAz+[0])])])
Char5=(IF[(getPL)=1]{)
Char6=(\n)(Count_Block) L X(KFA[(getXp)]) Y(KFA[(getYp)]) Z(KFA[(getZp)])
Char7=
IJ_G91Modus=0
CIRCLE_Modal=0
HELIXINTP=1
CIRCLERegisterPosition=(Count_Block)+(SPINDLE_Block)+(Char6)+(Char3)+(Backlash)+(Count_Block)+(Char1)+(KoordiChar)+(Koordi)+(KoordjChar)+(Koordj)+(KoordkChar)+(Koordk)+(Char2)+(KoordxChar)+(Koordx)+(}ELSE{)+(KoordyChar)+(Koordy)+(}ENDIF)+(Char5)+(KoordyChar)+(Koordy)+(}ELSE{)+(KoordzChar)+(Koordz)+(}ENDIF)+(CIRCLE)+(FEEDRATE_Block)+(Char3)
HELIXRegisterPosition=(Count_Block)+(SPINDLE_Block)+(Char6)+(Char3)+(Backlash)+(Count_Block)+(Char1)+(KoordiChar)+(Koordi)+(KoordjChar)+(Koordj)+(KoordkChar)+(Koordk)+(Backlash)+(Count_Block)+(HelixChar)+(AngleChar)+(Angle)+(Char4)+(CIRCLE)+(FEEDRATE_Block)+(Char3)
CircleSplit=0
CirclePolygon=0

[SPINDLE DEFINITION]
SpindleChar= S
ClockwiseRotationR= M3
ClockwiseRotationL= M4
HighValue=10000.00
LowValue=0.000000
Factor=1.00000
DecimalPlaces=0
Decimal=
ShowZeros=0
Char1= TOOL CALL (TNr) Z
Char2=
Char3=
SPINDLE_Modal=0
SPINDLE_Block=(Char1)+(SpindleChar)+(NUMMC)

[FEEDRATE DEFINITION]
FEEDRATEChar= F
HighValue=300.0000
LowValue=0.0
Factor=1.000000
DecimalPlaces=0
Decimal=
ShowZeros=0
Char1=
Char2=
Char3=
FEEDRATE_Modal=0
FEEDRATE_Block=(FEEDRATEChar)+(NUMMC)

[ToolChange]
Command1=(Count_Block) M9
Command2=(Count_Block)(SPINDLE_Block)
Command3=(Count_Block) M6
Command4=(Count_Block) TOOL DEF (TNrNext)
Command5=(Count_Block) L X(KFAx+[0]) Y(KFAy+[0]) R0 FMAX(SpiCW)
Command6=(Count_Block) L Z(KFAz+[0]) FMAX(CoolOn)
XChangeP=
YChangeP=
ZChangeP=

[TNr_Format]
NUMPlaces=1

[RegNr_Format]
NUMPlaces=1

[Comp_Format]
OutputPlus=
DecimalPlaces=3
ShowZeros=3

[SimConfig]
MESCAL=1.000000
TOSCAL=1.000000

[EntryCommand]
InsertAfter=0

[ExitCommand]
InsertAfter=0

[Cycle1]
CycleName=Drilling Cycle with chip breaking type G73
CyclePara=Approach height (A);Drilling depth (Z);;Number of chip breaks (Q);Dwell time at depth/top;
CycleType=0
SCommand1=(Count_Block) CYCL DEF 203 UNIVERSAL DRILLIN ~
SCommand2= Q200=(KFA[(CA)]) ;SETUP CLEARANCE ~
SCommand3= Q201=(KFA[-(Z2)]) ;DEPTH ~
SCommand4= Q206=(FeeF+[0]) ;FEED RATE FOR PLNGNG ~
SCommand5= Q202=(KFA[(Z2)]) ;PLUNGING DEPTH ~
SCommand6= Q210=(Round[(P2);2]) ;DWELL TIME AT TOP ~
SCommand7= Q203=(KFA[(Z1)]) ;SURFACE COORDINATE ~
SCommand8= Q204=(KFA[(CA)]) ;2. SETUP CLEARANCE ~
SCommand9= Q212=0.0 ;DECREMENT ~
SCommand10= Q213=(ABS[(P1)]) ;BREAKS ~
SCommand11= Q205=0 ;MIN. PLUNGING DEPTH ~
SCommand12= Q211=(Round[(P2);2]) ;DWELL TIME AT DEPTH ~
SCommand13= Q208=(getFEAB) ;RETRACTION FEED RATE ~
SCommand14= Q256=0.5 ;DIST. FOR CHIP BRKNG
SCommand15=(Count_Block) L X(KFAx+[0]) Y(KFAy+[0]) FMAX M99
LCommand1=(Count_Block) L X(KFAx+[0]) Y(KFAy+[0]) FMAX M99

[Cycle2]
CycleName=Left-hand thread with compensating chuck type G74
CyclePara=Approach height (A);Drilling depth (Z);;DWELL TIME AT DEPTH;
CycleType=1
SCommand1=(Count_Block) CYCL DEF 206 TAPPING NEW ~
SCommand2= Q200=(KFA[(CA)]) ;SETUP CLEARANCE ~
SCommand3= Q201=(KFA[-(Z2)]) ;DEPTH ~
SCommand4= Q206=(FeeF+[0]) ;FEED RATE FOR PLNGNG ~
SCommand5= Q211=(Round[(P1);2]) ;DWELL TIME AT DEPTH ~
SCommand6= Q203=(KFA[(Z1)]) ;SURFACE COORDINATE ~
SCommand7= Q204=(KFA[(CA)]) ;2. SETUP CLEARANCE
SCommand8=(Count_Block) L X(KFAx+[0]) Y(KFAy+[0]) FMAX M99
LCommand1=(Count_Block) L X(KFAx+[0]) Y(KFAy+[0]) FMAX M99

[Cycle3]
CycleName=Fine Boring Canned Cycle type G76
CyclePara=Approach height (A);Drilling depth (Z);Retraction (Q);DWELL TIME AT DEPTH;
CycleType=2
SCommand1=(Count_Block) CYCL DEF 202 BORING ~
SCommand2= Q200=(KFA[(CA)]) ;SETUP CLEARANCE ~
SCommand3= Q201=(KFA[-(Z2)]) ;DEPTH ~
SCommand4= Q206=(FeeF+[0]) ;FEED RATE FOR PLNGNG ~
SCommand5= Q211=(Round[(P1);2]) ;DWELL TIME AT DEPTH ~
SCommand6= Q208=(getFEAB) ;RETRACTION FEED RATE ~
SCommand7= Q203=(KFA[(Z1)]) ;SURFACE COORDINATE ~
SCommand8= Q204=(KFA[(CA)]) ;2. SETUP CLEARANCE ~
SCommand9= Q214=(KFA[(CQ)]) ;DISENGAGING DIRECTN ~
SCommand10= Q336=0 ;ANGLE OF SPINDLE
SCommand11=(Count_Block) L X(KFAx+[0]) Y(KFAy+[0]) FMAX M99
LCommand1=(Count_Block) L X(KFAx+[0]) Y(KFAy+[0]) FMAX M99

[Cycle4]
CycleName=Drilling Cycle type G81
CyclePara=Approach height (A);Drilling depth (Z);;DWELL TIME AT TOP;DWELL TIME AT DEPTH;
CycleType=3
SCommand1=(Count_Block) CYCL DEF 200 DRILLING ~
SCommand2= Q200=(KFA[(CA)]) ;SETUP CLEARANCE ~
SCommand3= Q201=(KFA[-(Z2)]) ;DEPTH ~
SCommand4= Q206=(FeeF+[0]) ;FEED RATE FOR PLNGNG ~
SCommand5= Q202=(KFA[(Z2)]) ;PLUNGING DEPTH ~
SCommand6= Q210=(Round[(P1);2]) ;DWELL TIME AT TOP ~
SCommand7= Q203=(KFA[(Z1)]) ;SURFACE COORDINATE ~
SCommand8= Q204=(KFA[(CA)]) ;2. SETUP CLEARANCE ~
SCommand9= Q211=(Round[(P2);2]) ;DWELL TIME AT DEPTH
SCommand10=(Count_Block) L X(KFAx+[0]) Y(KFAy+[0]) FMAX M99
LCommand1=(Count_Block) L X(KFAx+[0]) Y(KFAy+[0]) FMAX M99

[Cycle5]
CycleName=Drilling Cycle with dwell time type G82
CyclePara=Approach height (A);Drilling depth (Z);;Dwell Time;
CycleType=4
SCommand1=(Count_Block) CYCL DEF 200 DRILLING ~
SCommand2= Q200=(KFA[(CA)]) ;SETUP CLEARANCE ~
SCommand3= Q201=(KFA[-(Z2)]) ;DEPTH ~
SCommand4= Q206=(FeeF+[0]) ;FEED RATE FOR PLNGNG ~
SCommand5= Q202=(KFA[(Z2)]) ;PLUNGING DEPTH ~
SCommand6= Q210=0 ;DWELL TIME AT TOP ~
SCommand7= Q203=(KFA[(Z1)]) ;SURFACE COORDINATE ~
SCommand8= Q204=(KFA[(CA)]) ;2. SETUP CLEARANCE ~
SCommand9= Q211=(Round[(P1);2]) ;DWELL TIME AT DEPTH
SCommand10=(Count_Block) L X(KFAx+[0]) Y(KFAy+[0]) FMAX M99
LCommand1=(Count_Block) L X(KFAx+[0]) Y(KFAy+[0]) FMAX M99

[Cycle6]
CycleName=Deep Hole Peck Drilling Canned Cycle type G83
CyclePara=Approach height (A);Drilling depth (Z);Depth Increment (Q);Number of chip breaks;Dwell time at depth/top;
CycleType=5
SCommand1=(Count_Block) CYCL DEF 203 UNIVERSAL DRILLIN ~
SCommand2= Q200=(KFA[(CA)]) ;SETUP CLEARANCE ~
SCommand3= Q201=(KFA[-(Z2)]) ;DEPTH ~
SCommand4= Q206=(FeeF+[0]) ;FEED RATE FOR PLNGNG ~
SCommand5= Q202=(KFA[(CQ)]) ;PLUNGING DEPTH ~
SCommand6= Q210=(Round[(P2);2]) ;DWELL TIME AT TOP ~
SCommand7= Q203=(KFA[(Z1)]) ;SURFACE COORDINATE ~
SCommand8= Q204=(KFA[(CA)]) ;2. SETUP CLEARANCE ~
SCommand9= Q212=0.0 ;DECREMENT ~
SCommand10= Q213=(ABS[(P1)]) ;BREAKS ~
SCommand11= Q205=0 ;MIN. PLUNGING DEPTH ~
SCommand12= Q211=(Round[(P2);2]) ;DWELL TIME AT DEPTH ~
SCommand13= Q208=(getFEAB) ;RETRACTION FEED RATE ~
SCommand14= Q256=0.5 ;DIST. FOR CHIP BRKNG
SCommand15=(Count_Block) L X(KFAx+[0]) Y(KFAy+[0]) FMAX M99
LCommand1=(Count_Block) L X(KFAx+[0]) Y(KFAy+[0]) FMAX M99

[Cycle7]
CycleName=Right-hand thread with compensating chuck type G84
CyclePara=Approach height (A);Drilling depth (Z);;DWELL TIME AT DEPTH;
CycleType=6
SCommand1=(Count_Block) CYCL DEF 206 TAPPING NEW ~
SCommand2= Q200=(KFA[(CA)]) ;SETUP CLEARANCE ~
SCommand3= Q201=(KFA[-(Z2)]) ;DEPTH ~
SCommand4= Q206=(FeeF+[0]) ;FEED RATE FOR PLNGNG ~
SCommand5= Q211=(Round[(P1);2]) ;DWELL TIME AT DEPTH ~
SCommand6= Q203=(KFA[(Z1)]) ;SURFACE COORDINATE ~
SCommand7= Q204=(KFA[(CA)]) ;2. SETUP CLEARANCE
SCommand8=(Count_Block) L X(KFAx+[0]) Y(KFAy+[0]) FMAX M99
LCommand1=(Count_Block) L X(KFAx+[0]) Y(KFAy+[0]) FMAX M99

[Cycle8]
CycleName=Reaming Cycle Type G85
CyclePara=Approach height (A);Drilling depth (Z);;DWELL TIME AT DEPTH;
CycleType=7
SCommand1=(Count_Block) CYCL DEF 201 REAMING ~
SCommand2= Q200=(KFA[(CA)]) ;SETUP CLEARANCE ~
SCommand3= Q201=(KFA[-(Z2)]) ;DEPTH ~
SCommand4= Q206=(FeeF+[0]) ;FEED RATE FOR PLNGNG ~
SCommand5= Q211=(Round[(P1);2]) ;DWELL TIME AT DEPTH ~
SCommand6= Q208=(getFEAB) ;RETRACTION FEED RATE ~
SCommand7= Q203=(KFA[(Z1)]) ;SURFACE COORDINATE ~
SCommand8= Q204=(KFA[(CA)]) ;2. SETUP CLEARANCE
SCommand9=(Count_Block) L X(KFAx+[0]) Y(KFAy+[0]) FMAX M99
LCommand1=(Count_Block) L X(KFAx+[0]) Y(KFAy+[0]) FMAX M99

[Cycle9]
CycleName=Thread Cycle 207 without compensating chuck
CyclePara=Approach height (A);Drilling depth (Z);
CycleType=6
SCommand1=(Count_Block) CYCL DEF 207 RIGID TAPPING NEW ~
SCommand2= Q200=(KFA[(CA)]) ;SETUP CLEARANCE ~
SCommand3= Q201=(KFA[-(Z2)]) ;DEPTH ~
SCommand4= Q239=(ope[(getSPCW)=3?+:-])(Round[(getTW);3]) ; PITCH ~
SCommand5= Q203=(KFA[(Z1)]) ;SURFACE COORDINATE ~
SCommand6= Q204=(KFA[(CA)]) ;2. SETUP CLEARANCE
SCommand7=(Count_Block) L X(KFAx+[0]) Y(KFAy+[0]) FMAX M99
LCommand1=(Count_Block) L X(KFAx+[0]) Y(KFAy+[0]) FMAX M99

[Cycle10]
CycleName=Back Boring Cycle  type G87
CyclePara=Approach height (A);counter bore depth (Z);Off-center distance (Q);Material Thickness (M);Dwell Time;
CycleType=9
SCommand1=(Count_Block) CYCL DEF 204 BACK BORING ~
SCommand2= Q200=(KFA[(CA)]) ;SETUP CLEARANCE ~
SCommand3= Q249=(KFA[(Z2)]) ;DEPTH SENKUNG ~
SCommand4= Q250=(KFA[(P1)]) ;MATERIAL THICKNESS ~
SCommand5= Q251=(KFA[(CQ)]) ;OFF-CENTER DISTANCE ~
SCommand6= Q252=(KFA[(getTS)]) ;TOOL EDGE HEIGHT ~
SCommand7= Q253=(getFEAN) ;F PRE-POSITIONIN ~
SCommand8= Q254=(FeeF+[0]) ;F COUNTERSINKING ~
SCommand9= Q255=(Round[(P2);2]) ;Dwell Time ~
SCommand10= Q203=(KFA[(Z1)]) ;SURFACE COORDINATE ~
SCommand11= Q204=(KFA[(CA)]) ;2. SETUP CLEARANCE ~
SCommand12= Q214=1 ;DISENGAGING DIRECTN ~
SCommand13= Q336=0 ;ANGLE OF SPINDLE
SCommand14=(Count_Block) L X(KFAx+[0]) Y(KFAy+[0]) FMAX M99
LCommand1=(Count_Block) L X(KFAx+[0]) Y(KFAy+[0]) FMAX M99

[Cycle11]
CycleName=209 TAPPING W/ CHIP BRKG
CyclePara=Approach height (A);Drilling depth (Z);Depth for chip break;RPM factor for retraction;;
CycleType=6
SCommand1=(Count_Block) CYCL DEF 209 TAPPING W/ CHIP BRKG ~
SCommand2= Q200=(KFA[(CA)]) ;SETUP CLEARANCE ~
SCommand3= Q201=(KFA[-(Z2)]) ;DEPTH ~
SCommand4= Q239=(ope[(getSPCW)=3?+:-])(Round[(getTW);3]) ; PITCH ~
SCommand5= Q203=(KFA[(Z1)]) ;SURFACE COORDINATE ~
SCommand6= Q204=(KFA[(CA)]) ;2. SETUP CLEARANCE ~
SCommand7= Q257=(KFA[(CQ)]) ;Drilling depth SPANBRUCH ~
SCommand8= Q256=(KFA[(P1)]) ;DIST. FOR CHIP BRKNG ~
SCommand9= Q336=0 ;ANGLE OF SPINDLE
SCommand10=(Count_Block) L X(KFAx+[0]) Y(KFAy+[0]) FMAX M99
LCommand1=(Count_Block) L X(KFAx+[0]) Y(KFAy+[0]) FMAX M99

[Cycle12]
CycleName=Fine Drilling Cycle with dwell time  type G89
CyclePara=Approach height (A);Drilling depth (Z);;DWELL TIME AT DEPTH;
CycleType=11
SCommand1=(Count_Block) CYCL DEF 201 REAMING ~
SCommand2= Q200=(KFA[(CA)]) ;SETUP CLEARANCE ~
SCommand3= Q201=(KFA[-(Z2)]) ;DEPTH ~
SCommand4= Q206=(FeeF+[0]) ;FEED RATE FOR PLNGNG ~
SCommand5= Q211=(Round[(P1);2]) ;DWELL TIME AT DEPTH ~
SCommand6= Q208=(getFEAB) ;RETRACTION FEED RATE ~
SCommand7= Q203=(KFA[(Z1)]) ;SURFACE COORDINATE ~
SCommand8= Q204=(KFA[(CA)]) ;2. SETUP CLEARANCE
SCommand9=(Count_Block) L X(KFAx+[0]) Y(KFAy+[0]) FMAX M99
LCommand1=(Count_Block) L X(KFAx+[0]) Y(KFAy+[0]) FMAX M99

[CycleSimOptionen]
G80=;;;;;;;;
G73=203;;;Q201=;;Q202=;Q200=;Q256=;Q213=;Q211=;
G74=206;;;Q201=;;Q202=;Q200=;Q256=;Q213=;Q211=;
G76=202;;;Q201=;;Q202=;Q200=;Q256=;Q213=;Q211=;
G81=200;;;Q201=;;Q202=;Q200=;Q256=;Q213=;Q211=;
G82=200;;;Q201=;;Q202=;Q200=;Q256=;Q213=;Q211=;
G83=203;;;Q201=;;Q202=;Q200=;Q256=;
G84=206;;;Q201=;;Q202=;Q200=;Q256=;
G85=201;;;Q201=;;Q202=;Q200=;Q256=;
G86=;;;;;;;;
G87=206;;;Q249=;;Q250=;Q200=;Q251=;
G88=
G89=201;;;Q201=;;Q202=;Q200=;Q256=;Q213=;Q211=;
BORCYCLE_Z_INK=0
START_at_CALL=0

[USER]
TEXT=Brigdeport TNC_426VMC-1000/30