[Postname] Name=HurcoDinsIso (ISNC) KopfZeile= [Modul] PostModul= SIMModul= [StartCommand] Command1=% Command2=(Count_Block) (Condacam) Command3=(Count_Block)(TOOL_DATA) Command4=(Count_Block) (BLOCKMIN X(BX-) Y(BY-) Z(BZ-)) Command5=(Count_Block) (BLOCKMAX X(BX+) Y(BY+) Z(BZ+)) Command6=(Count_Block) G17 G40 G49 G71 Command7=(Count_Block) G75 G80 G90 Command8=(Count_Block) M25 Command9=(Count_Block) T(TNr) M6 ((ToolName)) Command10=(Count_Block)(SPINDLE_Block) Command11=(Count_Block) G00(Plane) X(KFAx+[0]) Y(KFAy+[0]) Command12=(Count_Block) Z(KFAz+[0])(CoolOn) [EndCommand] Command1=(Count_Block) M5 M9 Command2=(Count_Block) G00 M25 Command3=(Count_Block) M2 Command4=E [GENERAL] BlockPrefix= BlockEndPrefix= Extension=.fnc Decimal=. OutputPlus= CommentStartChar=( CommentEndChar=) XYPlane= G17 YZPlane= G18 ZXPlane= G19 LinetoCircle=1 LinetoCircleToleranceFactor=1.0 LinetoCircleRadius_MAX=1500 LinetoCircleSegment_MAX=5 LinetoCirclePlane_Code=1 GModal=0 CountChar=N NUMPlaces=0 Increment=2 StartUnit=2 Char1= Char2= Char3= Count_Block=(CountChar)+(Count) CoolOn=(ope[(RNrL+[0])=2? M7:(ope[(RNrL+[0])=3? M10: M8])]) CoolOff= M9 TimeFactor= [LINEAR DEFINITION] LinearMotion= G01 RapidMotion= G00 KoordxChar= X KoordyChar= Y KoordzChar= Z DecimalPlaces=3 XFactor=1.0 YFactor=1.0 ZFactor=1.0 ShowZeros=1 Char1= Char2= Char3= G40Comp= G40 G41Comp= G41 G42Comp= G42 XYZModal=1 LinearRegisterPosition=(Count_Block)+(Motion)+(CompOff)+(CompLeft)+(CompRight)+(KoordxChar)+(Koordx)+(KoordyChar)+(Koordy)+(KoordzChar)+(Koordz)+(FEEDRATE_Block)+(SPINDLE_Block) RapidRegisterPosition=(Count_Block)+(Motion)+(CompOff)+(CompLeft)+(CompRight)+(KoordxChar)+(Koordx)+(KoordyChar)+(Koordy)+(KoordzChar)+(Koordz)+(SPINDLE_Block) [CIRCLE DEFINITION] CIRCLE_R= G02 CIRCLE_L= G03 XZ_CIRCLE_R= G03 XZ_CIRCLE_L= G02 YZ_CIRCLE_R= G02 YZ_CIRCLE_L= G03 KoordiChar= I KoordjChar= J KoordkChar= K RadiusChar= R AngleChar= W HelixChar= I_Factor=1.0 J_Factor=1.0 KWR_Factor=1.0 ShowZeros=1 Char1= Char2= Char3= Char4= Char5= Char6= Char7= IJ_G91Modus=0 CIRCLE_Modal=0 HELIXINTP=0 CIRCLERegisterPosition=(Count_Block)+(Plane)+(CIRCLE)+(KoordxChar)+(Koordx)+(KoordyChar)+(Koordy)+(KoordzChar)+(Koordz)+(KoordiChar)+(Koordi)+(KoordjChar)+(Koordj)+(KoordkChar)+(Koordk)+(FEEDRATE_Block)+(SPINDLE_Block) HELIXRegisterPosition= CircleSplit=1 CirclePolygon=0 [SPINDLE DEFINITION] SpindleChar= S ClockwiseRotationR= M3 ClockwiseRotationL= M4 HighValue=10000.00 LowValue=0.0000 Factor=1.00000 DecimalPlaces=0 Decimal= ShowZeros=0 Char1= Char2= Char3= SPINDLE_Modal=0 SPINDLE_Block=(SpindleChar)+(NUMMC)+(ClockwiseRotation) [FEEDRATE DEFINITION] FEEDRATEChar= F HighValue=10000.0000 LowValue=1.0000 Factor=1.000000 DecimalPlaces=0 Decimal= ShowZeros=0 Char1= Char2= Char3= FEEDRATE_Modal=0 FEEDRATE_Block=(FEEDRATEChar)+(NUMMC) [ToolChange] Command1=(Count_Block) G00 G17 M9 Command2=(Count_Block) T(TNr) M6 ((ToolName)) Command3=(Count_Block)(SPINDLE_Block) Command4=(Count_Block) G00(Plane) X(KFAx+[0]) Y(KFAy+[0]) Command5=(Count_Block) Z(KFAz+[0])(CoolOn) XChangeP= YChangeP= ZChangeP= [TNr_Format] NUMPlaces=1 [RegNr_Format] NUMPlaces=1 [Comp_Format] OutputPlus= DecimalPlaces=3 ShowZeros=1 [EntryCommand] InsertAfter=0 [ExitCommand] InsertAfter=0 [Cycle1] CycleName=Drilling Cycle with chip breaking type G73 CyclePara=Approach height;Drilling depth;Depth Increment; CycleType=0 SCommand1=(Count_Block) G73 X(KFAx+[0]) Y(KFAy+[0]) Z(KFA[(Z3)]) R(KFA[(CR)]) Q(KFA[(CQ)])(FEEDRATE_Block) LCommand1=(Count_Block) X(KFAx+[0]) Y(KFAy+[0]) ECommand1=(Count_Block) G80 [Cycle2] CycleName=Left-hand thread with compensating chuck type G74 CyclePara=Approach height;Drilling depth; CycleType=1 SCommand1=(Count_Block) G74 X(KFAx+[0]) Y(KFAy+[0]) Z(KFA[(Z3)]) R(KFA[(CR)])(FEEDRATE_Block) LCommand1=(Count_Block) X(KFAx+[0]) Y(KFAy+[0]) ECommand1=(Count_Block) G80 [Cycle3] CycleName=Fine Boring Canned Cycle type G76 CyclePara=Approach height;Drilling depth;Retraction; CycleType=2 SCommand1=(Count_Block) G76 X(KFAx+[0]) Y(KFAy+[0]) Z(KFA[(Z3)]) R(KFA[(CR)]) Q(KFA[(CQ)])(FEEDRATE_Block) LCommand1=(Count_Block) X(KFAx+[0]) Y(KFAy+[0]) ECommand1=(Count_Block) G80 [Cycle4] CycleName=Drilling Cycle type G81 CyclePara=Approach height;Drilling depth; CycleType=3 SCommand1=(Count_Block) G81 X(KFAx+[0]) Y(KFAy+[0]) Z(KFA[(Z3)]) R(KFA[(CR)])(FEEDRATE_Block) LCommand1=(Count_Block) X(KFAx+[0]) Y(KFAy+[0]) ECommand1=(Count_Block) G80 [Cycle5] CycleName=Drilling Cycle with dwell time type G82 CyclePara=Approach height;Drilling depth;;DWELL TIME AT DEPTH; CycleType=4 SCommand1=(Count_Block) G82 X(KFAx+[0]) Y(KFAy+[0]) Z(KFA[(Z3)]) R(KFA[(CR)]) P(ABS[(P1)])(FEEDRATE_Block) LCommand1=(Count_Block) X(KFAx+[0]) Y(KFAy+[0]) ECommand1=(Count_Block) G80 [Cycle6] CycleName=Deep Hole Peck Drilling Canned Cycle type G83 CyclePara=Approach height;Drilling depth;Depth Increment; CycleType=5 SCommand1=(Count_Block) G83 X(KFAx+[0]) Y(KFAy+[0]) Z(KFA[(Z3)]) R(KFA[(CR)]) Q(KFA[(CQ)])(FEEDRATE_Block) LCommand1=(Count_Block) X(KFAx+[0]) Y(KFAy+[0]) ECommand1=(Count_Block) G80 [Cycle7] CycleName=Right-hand thread with compensating chuck type G84 CyclePara=Approach height;Drilling depth; CycleType=6 SCommand1=(Count_Block) G84 X(KFAx+[0]) Y(KFAy+[0]) Z(KFA[(Z3)]) R(KFA[(CR)])(FEEDRATE_Block) LCommand1=(Count_Block) X(KFAx+[0]) Y(KFAy+[0]) ECommand1=(Count_Block) G80 [Cycle8] CycleName=Reaming Cycle Type G85 CyclePara=Approach height;Drilling depth; CycleType=7 SCommand1=(Count_Block) G85 X(KFAx+[0]) Y(KFAy+[0]) Z(KFA[(Z3)]) R(KFA[(CR)])(FEEDRATE_Block) LCommand1=(Count_Block) X(KFAx+[0]) Y(KFAy+[0]) ECommand1=(Count_Block) G80 [Cycle9] CycleName=Drilling cycle retraction with spindle stop type G86 CyclePara=Approach height;Drilling depth; CycleType=8 SCommand1=(Count_Block) G86 X(KFAx+[0]) Y(KFAy+[0]) Z(KFA[(Z3)]) R(KFA[(CR)])(FEEDRATE_Block) LCommand1=(Count_Block) X(KFAx+[0]) Y(KFAy+[0]) ECommand1=(Count_Block) G80 [Cycle10] CycleName=Back Boring Cycle type G87 CyclePara=Approach height;Drilling depth;Off-center distance; CycleType=9 SCommand1=(Count_Block) G87 X(KFAx+[0]) Y(KFAy+[0]) Z(KFA[(CR)]) R(KFA[(Z3)]) Q(KFA[(CQ)])(FEEDRATE_Block) LCommand1=(Count_Block) X(KFAx+[0]) Y(KFAy+[0]) ECommand1=(Count_Block) G80 [Cycle11] CycleName=Fine boring cycle with dwell time and manual retract type G88 CyclePara=Approach height;Drilling depth;;DWELL TIME AT DEPTH; CycleType=10 SCommand1=(Count_Block) G88 X(KFAx+[0]) Y(KFAy+[0]) Z(KFA[(Z3)]) R(KFA[(CR)]) P(ABS[(P1)])(FEEDRATE_Block) LCommand1=(Count_Block) X(KFAx+[0]) Y(KFAy+[0]) ECommand1=(Count_Block) G80 [Cycle12] CycleName=Fine Drilling Cycle with dwell time type G89 CyclePara=Approach height;Drilling depth;;DWELL TIME AT DEPTH; CycleType=11 SCommand1=(Count_Block) G89 X(KFAx+[0]) Y(KFAy+[0]) Z(KFA[(Z3)]) R(KFA[(CR)]) P(ABS[(P1)])(FEEDRATE_Block) LCommand1=(Count_Block) X(KFAx+[0]) Y(KFAy+[0]) ECommand1=(Count_Block) G80 [CycleSimOptionen] G80=;;;;;;;; G73=;;;;;;;; G74= G76= G81= G82= G83= G84= G85= G86= G87= G88= G89= BORCYCLE_Z_INK=0 START_at_CALL=0 [USER] TEXT=Circular arc parameter I,J,K = absolut ISNC Mode